Are you tired of chilly drafts creeping into your home during the winter months? Or, perhaps you’re frustrated with the soaring energy bills that seem to chip away at your hard-earned money? If you can relate to these concerns, fear not! There’s a cost-effective solution that can transform your living space and save you money in the long run: foam insulation!
Introduction: What is Foam Insulation?
Spray foam insulation is a state-of-the-art technique that tackles the age-old problem of air leaks and poor insulation in residential and commercial properties. It involves the application of a specially formulated foam, which expands and hardens upon contact with surfaces, creating an impermeable layer of insulation. This revolutionary insulation method provides several valuable benefits that make it an excellent investment for both homeowners and businesses alike.
The Advantages of Foam Insulation
1. Enhanced Comfort
One of the foremost advantages of foam insulation is the drastic improvement it brings to your home’s comfort levels. By sealing every nook, cranny, and cavity, foam insulation prevents drafts and air leakage that often result in uneven temperatures and chilly spots in your living space. Say goodbye to shivering in one room while another feels warm and cozy – with foam insulation, you’ll experience uniform comfort in every corner of your home!
2. Superior Energy Efficiency
Foam insulation not only enhances comfort but also significantly reduces your energy consumption. Air leaks through poorly insulated walls, roofs, or crawlspaces can cause your heating or cooling system to work harder, driving up your energy bills in the process. By creating an airtight seal, foam insulation minimizes air leakage and maintains a consistent temperature within your home. The result? Reduced reliance on your HVAC system and substantial savings on your energy bills!
3. Sound Barrier
If you live in a bustling neighborhood or near a busy road, unwanted noise infiltration can be a constant annoyance. Fortunately, foam insulation doesn’t just prevent air leaks; it also acts as a sound barrier. Once the foam is in place, it works to reduce noise transmission from outside, providing you with a quieter and more peaceful living environment.
4. Moisture and Mold Prevention
Moisture accumulation and the subsequent growth of mold and mildew can spell disaster for your home’s structural integrity and your family’s health. Unlike traditional, porous insulation materials, foam insulation is impermeable to water, creating a moisture-resistant barrier that minimizes the risk of mold growth. Protect your home and preserve its value with the long-lasting effects of foam insulation!
5. Environmental Friendliness
In an era where environmental consciousness takes center stage, foam insulation is a green solution for energy conservation. By reducing energy consumption and decreasing your home’s carbon footprint, spray foam insulation plays its part in preserving the planet for future generations. Join the growing movement of environmentally responsible homeowners by choosing foam insulation for your property!
Conclusion: Invest in Foam Insulation for Unparalleled Comfort and Savings
If you’re tired of battling chilly drafts, persistently high energy bills, and unwanted noise intrusion, it’s time to consider foam insulation. With enhanced comfort, superior energy efficiency, soundproofing, moisture and mold prevention, and its eco-friendly features, foam insulation is an investment that pays off in more ways than one. Don’t settle for subpar insulation – enhance your home’s comfort, protect the environment, and save money by choosing foam insulation today!
When it comes to insulating your home or office, you want a solution that not only provides exceptional thermal performance but also offers long-lasting results. This is where foam insulation comes into the picture. Foam insulation, specifically spray foam, has gained immense popularity over the years due to its numerous benefits and advantages over traditional insulation methods. In this blog post, we will delve into the world of foam insulation, explore its benefits, and explain why it is the ideal choice for your insulation needs.
The Basics of Spray Foam Insulation
Spray foam insulation is a highly versatile and efficient form of insulation that is rapidly transforming the way we insulate our spaces. It is composed of two main components – isocyanate and polyol resin – that are combined using specialized equipment. When these components react, they expand and harden, creating a durable and superior insulating material. It can be seamlessly applied to walls, ceilings, floors, and even around corners and joints, ensuring a complete and airtight insulation solution.
Unmatched Thermal Performance
One of the key benefits of spray foam insulation is its unmatched thermal performance. The closed-cell structure of spray foam allows it to provide an air barrier, preventing the transfer of heat. This means that your home or office will maintain a more consistent and comfortable temperature, reducing the need for excessive heating or cooling. By minimizing heat loss or gain, you can significantly lower your energy bills and reduce your carbon footprint.
Increased Energy Efficiency
With energy conservation becoming increasingly important, spray foam insulation offers an ideal solution. Unlike traditional insulation methods, spray foam insulation offers superior energy efficiency. The airtight seal created by foam insulation greatly reduces air leakage and infiltration, ensuring that your HVAC systems don’t have to work overtime to maintain the desired temperature. With reduced energy consumption, you can enjoy substantial savings on your utility bills, all while contributing to a greener and more sustainable environment.
Enhanced Indoor Air Quality
In addition to its thermal and energy-saving benefits, spray foam insulation also plays a crucial role in improving indoor air quality. The air barrier created by foam insulation acts as a shield against outdoor pollutants, allergens, and even pests, preventing them from entering your living or working spaces. This can be especially beneficial for individuals with allergies or respiratory conditions, as it helps create a healthier and cleaner indoor environment.
Durable and Long-lasting Solution
Unlike traditional insulation materials, spray foam insulation offers exceptional durability and longevity. Once applied, foam insulation retains its effectiveness for an extended period, ensuring that you won’t have to worry about costly replacements or repairs. The inert nature of spray foam helps it resist mold growth and decay, providing a robust barrier against moisture and dampness. With proper maintenance, your foam insulation can last for decades, all while maintaining its insulation performance.
Conclusion
When it comes to insulating your home or office, choosing an efficient and long-lasting solution is of paramount importance. Spray foam insulation ticks all the boxes, offering unmatched thermal performance, increased energy efficiency, improved indoor air quality, and long-term durability. By opting for spray foam insulation, you can create a comfortable living or working environment, reduce your energy consumption, and even contribute to a greener planet. So, why settle for less when you can embrace the benefits of foam insulation? Contact a professional insulation contractor today and give your space the insulation it truly deserves!
Are you tired of dealing with high energy bills and uncomfortable temperature fluctuations in your home? Look no further! Foam insulation is the solution you’ve been searching for. With its remarkable effectiveness and versatility, spray foam insulation has become increasingly popular among homeowners. In this article, we will explore the numerous benefits of foam insulation and why you should consider it for your next home improvement project.
The Basics of Foam Insulation
Before diving into the many advantages of foam insulation, let’s take a moment to understand what it is and how it works. Foam insulation is a type of building material that is applied to walls, roofs, or other areas of a structure to provide thermal insulation. It is created by combining and spraying two liquid components – polyol resin and isocyanate – which then expand to form a strong, seamless, and solid barrier against heat transfer.
Enhanced Energy Efficiency
One of the key advantages of foam insulation is its exceptional ability to enhance the energy efficiency of your home. By creating a tight seal and preventing air leaks, spray foam insulation acts as a barrier against outside temperatures. This insulation method significantly reduces the need for excessive heating or cooling, helping you maintain a comfortable indoor environment throughout the year. As a result, homeowners often witness a remarkable decrease in their monthly energy bills, making foam insulation a smart investment in the long run.
Improved Comfort and Air Quality
Beyond energy efficiency, foam insulation also contributes to improved overall comfort and air quality within your home. Unlike traditional insulation methods, spray foam fills every crack and crevice, ensuring that no area is left uninsulated. This complete coverage eliminates drafts and cold spots, resulting in a more consistently comfortable home environment. Furthermore, foam insulation acts as an effective sound barrier, minimizing noise penetration from external sources, and promoting peaceful indoor surroundings.
Moreover, foam insulation helps maintain better air quality within your home. By sealing gaps and reducing outside air infiltration, it prevents the entry of dust, pollen, and other allergens, making it an ideal choice for individuals with respiratory conditions or allergies. The high-density nature of spray foam also inhibits the growth of mold and mildew, ultimately creating a healthier and safer living environment for you and your loved ones.
Long-lasting and Cost-effective
When considering insulation options, it’s important to choose a solution that will stand the test of time. With foam insulation, durability is not a concern. Once applied, spray foam insulation lasts for decades without deteriorating, maintaining its superior insulating properties over time.
Moreover, an investment in foam insulation can pay for itself in reduced energy costs. While the upfront cost of installation may be higher compared to traditional insulation options, the long-term savings on energy bills make it a cost-effective choice in the grand scheme of things. Additionally, the superior insulating qualities of foam insulation may increase the resale value of your home, making it an attractive feature to potential buyers.
Eco-friendly and Sustainable
In today’s world, where environmental consciousness is paramount, it is crucial to choose insulation methods that align with sustainability goals. Foam insulation excels in this aspect as well. By reducing energy consumption, spray foam helps reduce greenhouse gas emissions, making it an environmentally friendly choice. Additionally, foam insulation often contains recycled materials, further minimizing its impact on the planet.
Conclusion
From enhanced energy efficiency and improved comfort to long-lasting durability and environmental friendliness, foam insulation offers a multitude of benefits to homeowners. By creating a seamless barrier against heat transfer, foam insulation significantly reduces energy consumption and ensures a comfortable and healthy living environment. If you are interested in enhancing the insulation of your home, consider the power of foam insulation. It’s a wise investment that provides long-term advantages for both your pocket and the planet.
Polyurethane foam insulation is a contemporary and extremely efficient method of thermal insulation for structures. If spray applied, it can fill even the tiniest of gaps. It offers durable and sturdily-built insulation for homes, enhancing the quality of life and decreasing the cost of heating.
The most sought-after material used for construction insulation is polyurethane foam.
The disadvantages of other insulation methods allow us to conclude that it is among the most efficient structures to keep heat. The PUR foam insulation is distinguished by its quick application time and its high effectiveness.
Lower Heating Costs PUR foam‘s listing of advantages is extensive. One of them is the less expensive heating costs for the house. The Thermal-insulation properties that this product has been exceptionally high. It eliminates thermal bridges, thereby preventing heat from the house’s crucial points. This permits the retention of warmth in winter and also prevents the heat from escaping during summer.
The advantages of polyurethane foam can result in significant savings in energy and fuel expenses. The temperature of each room will remain at a consistent and comfortable level. The reduction of heat loss has an obvious impact on the reduction of the cost of heating. But this isn’t the only benefit that comes from polyurethane foam.
Quick Application Time The strength that is unique to polyurethane foam is its speedy and simple application (obviously, done by an experienced team). The PUR foam is applied with the spray method. It can increase its volume by several dozen times and then cures quickly. Spray insulation, as a result, is much quicker than insulation using other materials.
The benefit that comes with polyurethane foam lies in the simple application to lofts. Its material is perfectly adapted to hard and oblique surfaces. Because of the expansion of its structure, it gets into the tiniest of spaces which prevents the formation of thermal bridges. In case of slanted ceilings or tight spaces, it’s recommended to use polyurethane foam. The disadvantages of other thermal insulation materials render them hard to create tangible heating effects on difficult surfaces.
Incredibly Efficient Polyurethane foam is open-cell as well as closed-cell. Pur foam has an extremely low heat transfer coefficient l, making it one of the most effective and efficient materials for thermal insulation. It is extremely adhesive on the floor, invulnerable to wear and tear, and is extremely lightweight, meaning it will not overburden a building’s structure. Additionally, foam insulation is 100% safe for people suffering from allergies and pets. It doesn’t create dust, hold allergens, or harmful gasses. It will maintain a high degree of thermal insulation for several years.
Yeah, let’s make the phone Wow we’re on this stuff, really expand. Yes, it does. Kent by this product is shot on at about 1200 pounds of pressure and about 150 degrees heat it to the gun and the exothermic chemical reaction of the two products heats it up about another 40, 50 degrees, so about 200 degrees and 1,200 pounds of pressure, and It actually expands at a ratio of 1 to 120 well that stuff it covers every nook and cranny. Doesn’T it Ron you can bet you there‘s not going to be any cracks and voids with this product in the world and we‘re going to eliminate all those other infiltration factors that we were concerned with Ron? I noticed they’re shooting every other panel, how come they’re doing that. Well, there’s a reason for it and it facilitates the trimming and, if you’d like to step into the next room over here, I can show you how that’s done. Okay, let’s go! This is a trimming process and I promise to show you can’t, as you can see, that’s a special tool with a long saw blade on it, and what this does is affords us to cut the phone even with the faces of the studs, so that sheet rockers. Don’T have any problem when they come in behind us right. Okay, then, as you see the end of that sauce sticking out on the lift at that panel, adjacent to it was filled with foam as well would tear the fall and the next panel. So what we actually do is shoot every other battle back and trim. That is really slick Ron. I can see how this product works great in these 16 inch cavities, but are there any special applications for this product? Well, we like to think all applications of selection. 500 or special, but you’re, absolutely correct Kent. There are many specific areas in the house under new construction that just cannot be addressed properly and insulated properly with other installations. Let’S go look at some of those okay: let’s go Kent. This is the first of those special areas that we were talking about with a home and it’s what we call a subfloor, and we see a lot of this today. You know the architects are trying to use every square foot of the home that they can possibly literally have to. We see a lot of what they call bonus rooms and that’s what we’re looking at is the floor. Mother-Son floor of a bonus realm and with traditional types of insulation, hiring Arthur knows that type of thing are be too graphic. Those products are hollow inside and I’m sure you’ve got a lot of homeowners years that in all this one room, they just improve enough you, but, as you can see our product welds itself in the subfloor seals, if it‘s never going to shrink, it‘s never going to Sag, what you end up with is honestly just as comfortable as any other room floor as tremendous they make that over the rod, space very fun. I can’t here we are looking at another area of that requires special attention, and this is the trusses and that’s the end of the trusses between the top stud plate on the first floor and the bottom plate of the second floor right. These are just typical problems for air leakage in at home. If I were to ask you one more time, how would you insulate that, with traditional insulation such as fiberglass, what would your comment well not very easy that you get less than 16 inch width up there and they just have to stuff it up in their best? They can so it’s another cut and paste and patch job jewelry, that’s lutely. What would you do about a vapor barrier on that interior wall between those trusses? You can’t get a vapor barrier. This just can’t happen. You know one more time I got to say to you: can’t watch selection 500 go to work any doubt in your mind. If those trust sims are closed, I think they’re fairly. Well, sealed I‘m going to have a air leakage up there. I don’t think there’ll be much air hidden through that sticker cavity, which is good well, that is fantastic, even in between those small gaps in the trusses, where he fills those up you’re ready to look at another special area. You bet great, hey, Kent. This is another one of those special areas that we talked about: insulating with foam, we’re looking at a typical kitchen wall exterior wall, and we have plumbing and water supply, piping and wires, and electrical outlets and all sorts of penetrations in that role. If I were to ask you to insulate that wall with old fiberglass at one of the other, typical installations that are around, how would you go about it? What would you do well, it’d, be a cut-and-paste job around all that piping and electrical boxes in there. Okay, cut and paste, and the fiberglass is an example, ended up being compressed and what happens to your value when you compress my goes to almost nil okay, so we’ve got minimal insulation with traditional insulation techniques, desperate watch this we’re on look at that foam to surround All that piping in there, that is a I got your mind – that it completely encapsulates all those penetrations. No that’s just beautiful Kent. This is another one of the areas of special application, as you call it, and what we’re talking about our corners and T’s. If I were to ask you how that corner would get deep insulated with traditional installations on the market today, what would you say to me most, the time around that corner doesn’t get into it and the same goes for T’s right yeah! That’S that’s back watch this! That’S unbelievable another area we’re looking at here Kent that just really can’t be addressed by other installations or vaulted ceilings and cathedral ceilings that we see in many many of the homes. Today, again, those architects are gone nuts and trying to make them look pretty yeah. If I were to ask you to insulate this area with a traditional insulation fiberglass and that type of thing what‘s going to happen with time, well, it‘s going tobe nailed up there and in Sag down and and almost go to nothing overtime. Another thing we like to address is air-conditioning, duct leakage, the vent side of the air conditioning system operating at a positive pressure and the return side operating a negative pressure. A lot of leakage, plus the return side, is the primary source of dust leakage into the home. Dave and Ron this product is truly impressive. I’M just tremendously impressed, but as a builder, I got to ask you: what’s the bottom line of this product Kent, the bottom line is pretty simple: our comprehensive program of caulking sealing and insulating a home of selection. 500. It‘S going to give you about as comfortable a home as money can buy your home‘s going to be quiet, your home is going to be dust free and your home is going to be draft-free. Most importantly, your home is going to save you about 50 %. On your air conditioning and heating cost combine that with the elimination of any kind of an exterior Rep, the elimination in most parts of the country, vapor barriers and the downsizing of tonnage required to air-condition the home. So there’s substantial cost benefits on other products that we put in a home that will come back to us to help pay for the cost was less I’ve under the energy savings over the life of a 30-year mortgage is in the tens of thousands of dollars. Well, that’s impressive, and I know our consumers will love those savings that they’ll get off their utility bills. Well, Dave. I really appreciate you introducing me to this product is to render their product and Ron. I am building in my own personal home now and I can guarantee you this election 500 go in there and be the insulating product for me and my family to use, and hopefully several others thanks, my dear. Why thank you. Thank you.
Hi, I’m Shannon from host improvements comm and today, I’m going to show you how to use a two-part spray foam insulation package. There’S a lot of different manufacturers of these packages, so just depend of what’s available in your area, even though I’m going to show you how to use this particular one make sure you for sure read all the safety instructions and the user manual in whatever package you Get just to be sure that in case there’s, any differences from manufacturer to manufacturer, so the one we have today is a what they call a two hundred kit. So what they’re saying is that the yield on it will be about two hundred square feet worth of foam at one inch thick, so we’re gon na be spraying close to two inches thick here, so we’ll be hopefully getting around 100 square feet out of these two Cans at two inches thick, so once I opened up the box, some of the first things you find is you’re gon na find the instruction manual as well as the the you know: safety equipment, that’s needed and all of little tips and that sort of thing so Make sure you read that over well, most of these guys have 1-800 numbers and websites as well. So if you have other questions, you can get ahold of somebody to ask. You should find an assortment of some different spray. Nozzles. These guys send two different types and they they’ve sent about. I don’t know four or five of each one. It looks like so this particular nozzle here is just for spraying. You know gaps and cracks sort of thing. It’S gon na send out a stream, so that would be that one here this one here is a fan tip. It’S got a bit of a v-notch cut in the end, so this one’s gon na spray out about a I don’t know it just depends on the kit you’re using but probably eight inch or so fan width of pattern, which is good for filling wall. Cavities, like what we’re gon na do here, so you’ll have a bit of a selection of the of the tips in there. This kit comes with two two containers: two two steel cylinders. This particular one already has the hoses and the gun already hooked to it. That does have a bit of a carrying handle here as well. Some of the bigger kits they’re gon na have tanks to teach in tanks, obviously because it’s two components, but the tanks are much larger, so they come boxed separately just because they’re too heavy to to carry is one unit. So in here, like I said this, one, the the gun and the hoses are already attached to the tanks. Some of them you will, it will come with a wrench and you may have to attach your own hoses and gun a couple things to go over. I guess, since I’ve got the gun out putting on the tips, the gun has a bit of a safety trigger here this one. So the yellow button down here has to be compressed or pressed before you can actually squeeze the trigger. The tanks are still turned off by the way, so you don’t want to turn them on until you’re actually ready to spray. So this gun has a safety on it to attach a nozzle just get. It orientated wait right, there’s, usually some marks in the end of the gun that correspond to the the way the nozzle looks and just push it in there on this one, this little lever here, you should just hear it click in like that and just look to Make sure that the little believer hook down on the lock knob on the top of the nozzle so putting the nozzle on just like that, taking it off squeeze this button, pull it off when you’re spraying? If you stop, for more than about thirty seconds, you’re, probably gon na find that you’ll have to change your nozzle. So it’s a good idea, get yourself all set up, get things out of the way, so that, once you start spraying, you can just kind of keep going with it and you aren’t losing a bunch of time. Otherwise, you’re gon na have to change your nozzles. What happens is the two components come in each come in their own hose and once they hit the nozzle there’s a kind of a spiral II set up inside of the nozzle here that actually starts to mix the two homes, because until the two products mixed together, They don’t actually have the chemical reaction which causes them to expand and cure. So if you stop for too long, it starts to set up in here and it clogs, and it’s not gon na work properly. So that’s why they send you multiple ones. So if you stop pop your tip off, put a new one on and away you go again, they also in this bag sent some petroleum jelly. So what they’d like you to do is smear some of the jelly right inside of the gun here and that just helps to allow your your tips not to seal up rate at the end of the gun. So you can just throw your tip way put anyone on and everything should be fine, so we’ve got the jelly optimally. Your tanks need to be around are usually about 24 degrees Celsius around so that’d be what I don’t know about 79 78 degrees Fahrenheit to get the most yield out of them and to make everything work properly, so keep them somewhere stored. Warm you can spray on to a cooler surface, but you don’t want something. That’S frosty and wet so like here where we’re doing this in February and it’s a below grade. So the wall is cool, but it’s actually still about 2 degrees Celsius. So and there’s no frost present, so that’s your tanks once we’re ready to go we’re gon na open, both valves on the tanks completely you’re gon na see the product start to come down the line once once. It fills up the lines. Oh before that, sorry, you should shake the tanks really well. I think it’s usually around 3040 seconds. You need to agitate the tanks that will just get things mixed together, open your valves, let it bleed into the lines. Do your petroleum jelly, get your tip, ready and and then you’re pretty much close to being ready to spray, and obviously, before that, put on all your your protective equipment protective equipment? These guys recommend, if you don’t have real good ventilation, that you should be wearing a respirator similar to this and it’s fitted with cartridges that are for organic vapor as well as particle filtration, so they’re kind of a two-part cannister one. Does the organic part of the chemicals and the other just does the any solids that might be in the air? So so it’s important to have that if you don’t have the proper ventilation, we did a did. A video with us with a similar product there a while ago, and we had a lot of people freaking out because we weren’t wearing a mask. We did talk in the video, how we had lots of ventilation and everything, but we still had people kind of freaking out, so we’ve actually gon na redo this video today and we don’t have the ventilation here quite as good. We just were able to open a couple windows, so we’re gon na use the mask for sure also some rubber gloves to protect your hands. You already see that I have the the painters suit on or the bodysuit on, to protect my clothing, I’m wearing a hat I’ll, have safety glasses on. So it’s just to protect yourself from any spray back that you might get. It doesn’t happen very often, but you never know you could get some bounce back onto you so and it doesn’t come off that easily. You definitely don’t want it in your eyes or your mouth or anything like that. So so that’s for the protective part. I think I’ve I’ve shaken the tanks, pretty good, we’ll give him another little shake shake before we go just before. I actually use a nozzle and once I’ve got the tanks open, I’m gon na shoot the gun into a garbage can or a box or in our case, we’re gon na use. A garbage can just to make sure I’m getting two fairly even streams coming out. Then I’ll get my tip on and and start spraying, so when you’re spraying it’s much like kind of in a way like spraying paint. If you’ve ever had to do that, we’re gon na come up to the wall. We want to be about six or eight inches away from the wall and we’re just gon na. You know, regulate our speed by hand to put on the amount that we want to see get on now. Remember it’s going to expand some, so you don’t want to fill the cavity rate up right away or once it expands you’re just gon na be having to cut it all off, because it’s it’s sticking out too much. You know. So it’s simply squeeze the trigger regulate. Your speed let go of the trigger squeeze and come down again. Okay, so you just keep doing that. We’Re gon na do these some of these spaces here in preparation. What we’ve done any electrical boxes, you’ll want to tape them up or seal them up, because once the foam gets in and around them, it’ll actually expand into the the open holes and cavities of the box and actually end up inside. So you want to prevent that. So we’ve just wrapped this one in some plastic, the wiring is fine to be embedded in the spray foam that isn’t a problem. We’Ve just basically brushed the wall off, made sure it wasn’t covered in any cobwebs and dust and that if the wall is damp or frosty or anything you you want to make sure you warm it up and dry it off before you spray this on that won’t Bond to the concrete as well, you will get some probably overspray onto some of your framing materials here. We’Ve just got two by twos, but that will clean off with a scraper fairly easily once it secured anything. That’S around the area that you don’t want to get foam on, just Paulie it up or tape it off or whatever. Just to be sure you aren’t getting some overspray on anything that you didn’t want to cover so we’re gon na spray. Some rate on this concrete wall, I’m gon na, go up and do a couple cavities in that wood wall too. It’S really just the same thing, but I just thought: I’d show it since we can. I think that’s pretty much covering everything that I’d talked about again. Remember just keep your foam canisters at a good temperature. These ones actually have a little temperature gauge on them. So that’s kind of handy to know where you’re at but just keep them inside, so they’re they’re warmed up and good to go. You don’t want to directly. You know blast a furnace on them or wrap them in electrical heat blanket or something like that, not nothing that extreme, but just make sure they’re warmed up well, okay, so I’m going to put on my protective equipment. You may not be able to hear me as well with the mask on so that’s why I was trying to cover everything here well before I get all suited up, but I may may do bit of talking with the mask on, but it may not be that Clear so so I’m just going to break away here for a minute, get my personal, personal, protective equipment on and then we’ll come back and show you how to spray [, Music, ], [, Music, ], [, Music, ], [, Music, ], [, Music, ], [, Music, ] [, Music, ] [, Music, ], [, Music, ], [, Music, ], [ Applause, ], [ Applause, ], [ Applause, ], [, Music, ], [, Music, ], okay, so we’ve let things sit here for a little bit and let the fumes get out. So we can take the mask off and finish up. You can see it’s expanded out nicely, it’s nice and firm. If you get a wrong mixture, sometimes you’ll get a clogged line or something. So if you get too much of one of the chemicals – and I can’t remember – which way it is you’ll actually get soft mushy foam and if it goes, the other way where the other chemical is is too much. The foam is really brittle in and it almost just doesn’t stand up. If you touch it, it actually crumbles away right away where this is well. This is good. This is nice and firm. That’S exactly what we want so now. The next step that we’re kind of at and some actually something I didn’t mention – was in most areas. If you spray up the two inches, you more than likely will not have to put the poly vapor barrier on the inside, so just check with your local codes. On that, the one thing to consider when doing that, and you notice that I put on two to three different coats like passes, so that those first couple get a chance to actually cure before you cover them up and form that skin over it, which gives you That that airlock or that air stoppage, because what’s gon na happen now you can see where some of this foam has expanded past the actual framing. So I’m gon na go back. You know and trim it back flush. So now, if I did had done that all in one pass now that I cut that that probably compromises the vapor barrier, qualities of it where because I’ve got those couple passes in behind that, I’m not going to be cutting into. In my opinion, that’s still pretty good, so in this case we’re we’re actually only in most in a lot of this we’re a little less than an inch and a quarter or inch and a half thick. So we’ll we’re gon na need and from my area, we’re gon na need another vapor barrier anyways, but something to consider so, if you’re free, if you’re spraying into a 2×4 wall where you’ve got the the ability to spray at two or two and a half inches Thick go ahead and do it check with your local Building Authority because you may not have to put a vapor barrier over after okay, let’s move on so we’ve got it all sprayed. You can see I’m just taking a utility knife and just shaving this down flush with the studs and just clean it all up peel it off. So you just go around, do all that, because otherwise, if it’s sticking out and you go to drywall over top of that, it’s it’s gon na give you some issues with pop screws and that sort of thing. Okay, so just keep going around another thing you can use is the old handy red bar scrape things down, get right, underneath it scrape it off like that once the foam is, is its secured point. This is not hazardous anymore. You can throw this right in the garbage, don’t eat it, throw it in the garbage, but you don’t you don’t need the mask. I don’t really even need the gloves on anymore, but just go around. Get things cleaned up so that it’s all good for when you want to put the finishing touches over top of it? What else did I forget anything? I think that I think that should cover it so now you’ve seen how to do it. This may not be the most economical way if you’re gon na do a whole basement. These kits aren’t aren’t real cheap. It might be cheaper to actually have a pearl come in and give you a price to do the whole thing. If you’re in a remote area, though this might be the only option you have, if you’re gon na do a you know a couple rooms or a little bit of space, then also again, it might might still be very economical to do it like this. This stuff works really good for joist ends as well so, and we do have a video on that. So if you want to check that out so yeah, I think that’s all. I can tell you so that again, I’m Shannon from house improvements and if you want to go to our website, you can check out the forum. Ask any questions you might have about this on there and I’ll get get a reply off to you as soon as I can, and also you can check out our YouTube channel and see all the other videos we have thanks for coming and watching.